China Custom Leather Jackets & Coats Factory | Private Label Leather Garment with Your Logo

Home / All / Leather Jackets / Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique

Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique

Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique
Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon AppliqueCustom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique
Share
CategoriesLeather Jackets
BrandDanke Leather Garment Manufacturer
Product SpecificationsQ4-080
DownloadDownload pdf
Detail Information

Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique

  • Material: bone faux leather at roughly RGB 221, 211, 194, a clean warm off-white with even fine grain and genuine leather applique patches.
  • Craft: flat leather applique with two-tone pieced balloon envelopes, chain-stitch gores and wind lines, satin edging, chenille inside the lettering only.
  • Cut: angled asymmetric zip under a wide charcoal flap, charcoal pointed collar, two zip pockets, rust red yoke with a stud row, no belt.
  • Wear: spring and autumn city wear, evening outfits on a pale ground, and travel where a light leather-feel layer is enough.
  • Order: custom made to order in your measurements, colourway and label, with sampling and quantity pricing for larger runs.

Biker Jacket in Bone Faux Leather

A bone faux leather biker jacket cut on an angled charcoal front and a deep rust red yoke, with a two-tone balloon rising across the back.

The base is faux leather, a non-animal material with even fine grain, light weight, easy care and no dependence on the size and growth marks of a hide, so a large pale ground and high-consistency colour blocking can be carried steadily with no shade break between pieces. Bone here is the measured colour at roughly RGB 221, 211, 194, a clean, bright, warm off-white that does not yellow, soil or dull. On a pure white studio ground the charcoal angled placket flap and the deep rust red yoke give the contrast, and a soft natural shadow keeps the silhouette readable. The applique patches are genuine leather, cream, deep rust red and charcoal, cut and combined with the faux base, so the garment is a leather-patch and faux-base combination rather than an all-leather jacket. Front and back are measured to match, and nothing is recoloured, vignetted or pushed in saturation. Material type, thickness, hand, colour and finish can be specified against a swatch and shade card.

Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique — custom size sheet and construction detail

Applique and finishing

Applique leather patch is the main craft on both faces. The balloon on the right chest, and on the back FLOAT, the large balloon, ARMORWOOD and the mirrored side balloons are all separately cut flat leather pieces with a smooth face, visible grain and a crisp cut edge, edged in satin stitch. Chenille fills only the inside of the ARMORWOOD strokes, keeping the flat face of the patches intact. Chain-stitch draws the two gores across each balloon, the inner lines of FLOAT and the rising wind lines on the back, and satin outlines each balloon and edges the letters. Every balloon is built as a two-tone pieced envelope: cream leather for the upper section, deep rust red leather for the lower, two independent pieces joined on a horizontal seam rather than a printed gradient. Small silver studs run along the lower edge of the deep rust red yoke front and back. There is no rhinestone, crystal, sequin or hot-fix stone anywhere, and no backing plate; the wind lines are pure stitching.

Custom Men's Bone Faux Leather Biker Jacket with Two-Tone Balloon Applique — applique and finishing detail

Cut and finish

The silhouette is a biker jacket: an angled asymmetric zip running from the wearer's right shoulder down to the left hip under a wide charcoal leather placket flap, a charcoal leather pointed collar with snaps, two zip slanted pockets, charcoal leather cuff bands, a straight hem, a square body ending at the hip with sleeves to the wrist. The collar runs right around the neck at one height front and back and the charcoal cuff bands match front and back; the angled zip, the wide flap and the two pockets are front only, leaving that line clean on the back. A deep rust red leather yoke crosses the chest and continues over both shoulders at the same height on the back, edged with a fine charcoal satin line and the stud row. There is no belt. Length, sleeve, chest ease, collar shape, zip direction and flap width, pocket position, yoke depth and cuff and hem treatment are built to your specification.

Specifications

MaterialBone faux leather with genuine leather applique patches
StyleBiker Jacket
CraftLeather applique with two-tone pieced balloons, chain-stitch gores and wind lines, satin edging and silver studs
ColorBone, charcoal black, deep rust red
CollarCharcoal leather pointed collar with snaps
ClosureAngled asymmetric zip with wide charcoal placket flap, front only
Order TypeCustom made to order

Who it is for

For menswear buyers, boutique owners and private-label brands looking for a made-to-order bone biker jacket with applique work.

Care notes

  • Wipe with a soft dry cloth; keep away from prolonged direct sunlight and direct heat.
  • Do not machine wash or tumble dry; professional leather cleaning only.
  • Shipping and delivery times are confirmed per order — contact us for your destination.
Contact Danke
With over 30 years of experience in clothing manufacturing, DANKE is your one-stop destination for private label custom Leather Jackets & Coats. We provide comprehensive factory services to meet all your needs.Leather Jackets is not just clothes, it reflects a culture of individuality. Warm welcome purchasing manager, individual clothing brand owners & designers, and wholesaler, ects. Email us your specific inquiries.
*Email
Name
*Phone
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.
Address
Review
  • 加载中···